Can I just start out with a WHOO?!

And a WHEW!! Cause I’m exhausted.

:)

It’s been two months since I’ve addressed my office redo, and I’ve had the mdf for the board and batten treatment on the walls for about that long. It’s been piled in the garage all that time…and every time I’ve stubbed my toe, tripped over them or watched them gathering dust since January, I have thought… I MUST get that project done.

And I just kept thinking. No doing. :)

I was hesitating because for this space, I really, really wanted to pull out the baseboards in the office before I installed the B and B treatment. I wanted to install fat, thick ones like in the inspiration picture I showed you a while ago:

So I hesitated. And worked on purging. Did a little change in the living room. And took a couple trips to IKEA. :)

I hesitated because as I’ve mentioned before, our baseboards are SUCH a pain in the booty to remove. I’ve done it in a bathroom and our laundry room, and oh. my. good. NESS. – they are so hard to get off the wall. It’s just crazy. I’m talking two inch, thick nails holding those puppies in.

Every time I’ve done it, I end up damaging the drywall, which has been OK because I’ve installed beadboard. But in the office, I was sceered. I knew some damage would be covered by the boards, but not all. But I was also afraid to not take them out – would it look wonky? Unfinished? Wrong?

Well, I was looking at the blank walls of the office yesterday morning and just decided to take a risk and just install the stuff already. I wasn’t going to rip out the baseboards -- I would just install the mdf boards right over them. I knew it wasn’t going to be perfect, but none of my projects are. They all have little imperfections and quirks – that’s how I roll. Why stop now? :)

I just wanted to get it done and said to heck with perfect. I was going to get my vision up on the walls!

And once I started, it was hard to stop. I got everything done yesterday and today. I started with my primed boards from Lowe’s:

They’re 3 1/2 inches wide, 3/4 inch thick and came in 12 foot lengths. I had them cut in half so they were easier to work with. I would have had them cut from a sheet of mdf like I did on the staircase, but I really wanted primed mdf for this project.

There’s a LOT of wall space to cover this time. And to paint. :)

I started by nailing the boards along the bottom over the baseboards:

And I wasn’t horrified. :)

I used my nail gun and two inch nails to install all of the mdf. I wanted something thick enough to get through the boards, the drywall, and into the studs (where I could get them).

Then I figured out how tall I wanted the treatment, and started putting up the vertical boards. I cut a 13 inch board and used it as my spacer between each vertical piece, then put the boards along the top:

I was loving how it was coming along, but I wanted a little more character, so I added a some detail by adding another line of boards:

I went ten inches down from the top boards. I waffled between ten and 12 inches, and wish I would have thought about the light switch before I decided on the ten:

:) Again, SO not perfect. But with some caulk, spackle, and some paint, you won’t even notice it in the end. Pinky swear. The lamp in front of it will help too. ;)

I was so in love with how it turned out! But I still wanted to add a little somethin’ -- it was the detail I had seen in my head all these months, and I knew I had to do it.

So, it was back to Lowe’s we went to grab some more primed mdf, but this time it was the 1 1/2 inch width:

I took the smaller mdf and created a shelf around the top of the board and batten:

I just nailed it down into the 3 1/2 inch boards that went around the top. It’s super sturdy – I didn’t even use glue. 

I found that small trim (looks like mini-crown molding) to put along the bottom, under the “shelf.”

The hardest part in the room was this area by the doors – the corners took 22.5 degree cuts instead of 45’s;

They just took a few extra practice cuts. ;)

You can see how they came together where it hits the window:

It’s gonna look fantastic once it’s all painted!

The imperfections are everywhere – I spaced the boards around the room based on light switches and plugs, but I completely forgot under the windows. So when I went to add the boards under the sills, I realized the measurements were way off.

I figured since I’ll always have drapes up, I decided to wing it and just put one single board right in the middle of the window:

You won’t see the empty space where there should have been other boards, because it’ll be covered by drapes. *ThankyouLordforfabric.*

Because I was working around a plug, I ended up not having enough room for a whole board in one corner. I went ahead and put it up, so one section is about half an inch smaller than the others:

Can you tell which one it is?

Wait, don’t answer that! Just say you can’t tell. ;)

I had to do that in a couple spots, but I’m about 150 percent sure I’m the only one who will notice when it’s all painted. And even if they do notice, I’m quite sure I’ll be the only one who cares.

I finished it all off by putting up the trim around the windows:

Most of that will be covered by the drapes too, but I just love the look!

And now, the room is finally coming together!:

It only took 43 foot boards, which ended up being about 118 cuts, 150 trips in and out of the garage, and climbing up and down something like 624 steps.

Or so. :)

Needless to say, I haven’t needed to work out this week.

It’s far from complete, but I can finally see my vision coming to life:

That’s my DIY memo board leaning there – I need to figure out how I’m going to hang it with the addition of the ledge. I think I’ve figured it out.

Next up – caulking, spackling and sanding. If that’s not enough to make you cry a few tears, after that it will need a couple coats of paint. Whimper.

(Yet again, I have not followed my own advice of painting before installing.)

But I’ve gotten this far, I know I can DO THIS people!

Then I can get moving on the drapes, accessories and art:

I didn’t want the ledge to stick out too much, but I wanted it to be just wide enough to hold frames.

Here’s one of my favorites, waiting on the perfect spot:

It’s soooo dreamy. :)

But for now, our garage looks like a sawdust bomb went off:

And my shoulders are practically screaming at me. :)

I showed you some of the board and batten installation details in a video in this post. It isn’t hard – I swear to you. It’s time consuming, but not hard. I use a nail gun and compound miter saw for this project. You can do it by hand, it will just take you a lot longer and you’ll need a few more shoulder massages. ;)

I used 19 primed 3 1/2 boards, 12 feet each, and the total cost for those and everything needed for the ledge ended up right at $200.

I can’t believe how far this room has come – the before:

And now:

Can you believe it’s the same room? I can’t, and I live here. ;)

And you know what – I don’t even notice my whack baseboard/mdf board combo. It really doesn’t bother me. I took a risk at having it less than perfect and I’m so glad I did.

I’m linking this up to my friend Nester’s Take a Risk Day party! Have you taken a decorating risk lately? 

Well hello there!! I am just overwhelmed at your response to my last post. You made me feel SO much better! :) I was so happy to read your comments and to hear many of you are making time to take care of YOU! It made my week! (Really.)

Because of I’ve been organizing like mad, and throwing in a few more work outs in here and there lately – my DIY/crafty/decorating time has been suffering. :) I rectified that today with a project I’ve been meaning to do forEVER.

I needed a new memo board for the light and bright office redo I’ve been working on. I made this one years ago:

It’s looking a little sad now. :) To make it, I just covered a piece of insulation foam with fabric. I wrapped the ribbon around it and hung it -- done!

I wanted something huge and it worked perfect! (See that squishy face in the picture on top? That’s my Bub’s birth announcements. Still LOVE.)

Well, about a year ago (yes, a YEAR) I found this huge frame for $10 at Goodwill:

I think it was even half off – it’s been so long I can’t remember! I knew it would work perfect for a new memo board. (I was planning ahead.)

I liked how chunky the frame was, but it wasn’t in the best shape:

It also had a band of linen-type fabric that I actually quite liked.

I had a plan in mind for this baby and I absolutely luuuurve how it turned out! Not just love – LURVE.

First step was to prime the heck out of the sucker. I laid it down on my “spray painting” sheet on the garage floor and did a couple quick coats.

I need to mention that it was NINE degrees outside when I did this. It was unreal, it was so cold.

I am nothing if not dedicated! :)

Once I got feeling back in my hands, I brought it inside to dry. (Spray paint takes forever to dry in extreme temps.)

After that it was ready for paint. Because I wanted to use only what I had, I painted it the blue ceiling paint I used in the office. While it was drying, I moved onto the “memo” part:

This stuff is that thick foam insulation you can get at the hardware store. I love it! I got a few sheets to cover our crawl space openings into the basement years ago. It works GREAT – keeps the cold and the spiders out! Eww!

Anyhoo, I wanted to reuse the foamy stuff for this memo board as well. I measured the size I needed, then used my Dremel to cut it out:

Awe-some!! (Said in a sing song voice.)

I wrapped it with my fabric, securing it to the back with hot glue:

I nail gunned it to the back of the frame and it worked like a charm!

For now it's hanging right behind the desk:

I think it will stay on that wall, but not sure where exactly. :) My plan for the board and batten includes a small ledge, so after that’s done I’ll have to play around with the memo board.

Of course I used the stripe fabric, which is a pain in the booty to get just right:

It has to be perfectly straight or it will drive. you. MAD. Or maybe it just drives me mad. :)

When I primed the frame, I sprayed right over the linen fabric (one word: L.A.Z.Y.) and the primer didn’t even cover it. So weird – it looks just like it did before!:

I just left the little gold strip inside the frame primed. Again…laaaaazy.

I got the fabric pretty straight:

Enough that it doesn’t give my hives to look at it. :) It’ll be covered with notes anyway. That’s what I keep telling myself.

Did you notice my little addition to the DIY drum shade fixture?:

A picture in a magazine inspired it – I saw a beautiful drum shade trimmed out with beautiful, large glass beads. It was GORG. I searched ev.er.y.where. online and couldn’t find anything that looked like it – and then one day I checked out Hobby Lobby and found this.

It is just a precious little beaded trim – I adore it:

Is it possible to be in love with cute beaded trim? Is it normal to be in love with cute beaded trim? I don’t care – I am. :)

I am loving how the room is coming along! The time has come though – I need to buck up buttercup and just get that board and batten DONE.

I still can’t believe the transformation so far. The office before:

And after:

WHOO! Love it! And my office will be extra insulated now. ;)

**I still don’t know what I’m doing with that chair – the cover I had was the wrong blue, (total clash with the memo board) so I took it off for now. I think I have something in mind. (Do you hear my mind crankin’?)

Hope you have a fantastic weekend!!

Hello all! Hope you have a great weekend planned!

I’ve had a little obsession that’s grown over the past six months or so…and I never thought it would happen. My obsession used to give me heebs and totally freak me out. But I’ve learned to love -- Craig and his list. :)

The heebs I used to get were actually more about selling than buying. And I’m still not a big fan of the selling part. :)

But I’m a complete convert on the buying part. Gah. I’m hooked. Part of the problem is it’s so accessible with my iPhone app – it is AWESOME. Just like Facebook and Twitter, I only use it on my phone, never on the computer. It’s so convenient – you can save searches, save preferences, and the best part – the pictures pop up in the list. It’s SO easy to use! And it was FREE. Score! (You’d think I was paid to say that, but no. It’s that good.)

I usually spend five minutes every day or two scrolling through, even when I don’t need anything. That’s how they get ya. :)

Last summer, Craig had me at hello when I did some searching and found this (Drexel!) dresser for only $100:

It was a perfect fit in our family room! I absolutely LOVE it.

I had hoped that dresser would fit in our foyer, but it was too long, so a short time later, I searched again, and found this buffet that ended up in our foyer:

Sahweeet! I was starting to fall in love…with Craigslist. :)

I’ve since bought a few more pieces, (one for an absolute STEAL – I’ll show you soon!). I mentioned last week that there was a dresser I saw for my office that made my heart go pitter pat. That particular one sold before I could get my hands on it, but the seller had another beauty she hadn’t listed yet:

I love her, I do.

The dresser, not the seller. But I’m starting to love her a little bit too – she’s the one that sold me the buffet in our foyer. ;)

I love her pretty detail:

Her little legs and curvy lines:

And all of her STORAGE. :)

Awesome!! Isn’t it just calling out for some beautiful glass knobs?

She’s old and solid cherry wood with dovetail drawers. There’s a medallion inside marked Huntley Furniture, which I had never heard of. (I did some research and found out the company started in 1906 and phased out around 1961.) I’m finding part of the fun of these finds is researching their history. :)

I don’t know yet if it will stay black (although I think just about any room can handle one black piece). I’m going wait a bit, see how the room comes together, then decide.

The two lamps on top are from Target, and I got them just today.

I’ve passed by them over and over for about two weeks, and drooled over them each time. I mentioned it on Twitter this morning, and I tell you what – it’s like having hundreds of girlfriends shopping with you, with their “Get them!,” and “Go now before they’re gone!” (put the fear in me) and “Do it, you totally deserve it!”

OK, I may have added the last one myself. Whatever.

Anyway, they are absolutely STUNNING. The pictures don’t do their pretty aqua color justice – but oh my, I adore them:

Thump to the chest at ya, Tweeps!! :)

I’ve learned a few things in my short time as a Craigslist convert that I always follow:

1. I email first, using an old email with my maiden name. Call me crazy but I don’t want anyone to know my first and last name unless I’ve communicated with them a few times. Actually, I still don’t tell them my last name, even when I buy. :)

2. GET DIMENSIONS (save yourself a drive, gas money, time, etc.)

3. If you go to check it out, bring someone with you, or at least tell someone where you’re going. And I never bring my son with me.

4. If you don’t like it, if it’s not right, if it’s the wrong size, you DON’T have to buy it. :) Just tell them it’s not quite right, and go on your way. If you feel weird, just say you need to check some measurements at home.

5. I always ask if the piece is wood. Especially with something like a dresser, where sometimes the top is laminate, the drawers are wood. I want something I can paint (fairly) easily and that’s a sturdy wood piece.

I found a few treasures just waiting for a redo on the Indy Craigslist that I wanted to share with you!

This vintage dresser would be absolutely stunning painted in just about any color:

Wouldn’t that be gorgeous in a small foyer or mud room? And it’s only $40!

I love this mid-century piece:

It’s possibilities are endless – perfect for an office, as a TV stand, even just a dresser. It’s priced at $250, which is a little steep, but the seller says it’s a Miller Desk piece. I hadn’t heard of that company, but a quick search tells me they were based in High Point, North Carolina. And most times, High Point equals high quality. :)

This one is very similar to mine, just a tad simpler:

It’s got great, deep drawers. The price for this one (wood throughout, vintage, dovetail drawers) is only $100! Just think about what it would cost to get a dresser with this quality and size at any furniture store – you can’t beat it! 

I found a few tables I loved too – this sofa table could be gorgeous!:

And people, it’s only $20!! Five and a half feet long and $20? A coat of paint and it’d be good to go. If only I needed a sofa table. :)

This one looks like it came right out of the Pottery Barn catalog:

I LOVE it’s shape – so unique! And only $60. THIS is why I a Craigslist convert!

And this one is stunning as well:

Look at that detail! OH my. Wouldn’t that be a fantastic craft table? I’m drooling. It says to make an offer – and who knows what you could get it for? It’s way down on the list, which means it’s either sold and they never removed it (hate that!) or it’s been a while since they posted and are really ready to get rid of it! :)

So there you go – one of my latest treasures from my friend Craig, some tips from a newbie, and some fantastic inspiration to get you to just look already!! :)

Sooo…what fatabulous stuff have you found from Craig? Do you sell and a buy, or just browse (and occasionally buy) like me? Do tell!

P.S. The (free) app I use is called CraigsPro. You can pay to upgrade it, but I haven’t found a reason to do so. It rocks.